• home
• supercubers
• flakers
• dispensers
• filters & cartridges
• contact MisterChill

Six Series

• ACM 46 - £696.00
• ACM 56 - £867.00
• ACM 86 - £1050.00
• ACM 106 - £1194.00
• ACM 126 - £1395.00
• ACM 176 - £1861.00
• ACM 206 - £2400.00
• ACM 226 - £2539.00

view all

Dice Cubers

• MV300/B393 - £1976.00
• MV450/B393 - £2437.00
• MV450/B550+KBT1MV - £3683.00
• MV600/B393 - £2763.00
• MV600/B550+KBT1MV - £3309.00
• MV1000/B550+KBT1MV - £4502.00

view all

Installation

Click to download printable PDF versions:

• Ice Makers / Crushers
• Water Filter Kits / Cartridges

Installation of Water Filter Kit

1. Screw brass fittings supplied into threaded holes on filter head using P.T.F.E. tape, and tighten.
2. Secure filter head to wall.
3. Fit 750mm long hose to brass fitting on inlet side of filter head.
4. Connect other end of this hose onto the water supply stop valve.
5. Connect hose supplied with ice machine to brass fitting on outlet side of filter head.
6. Remove protective wrapper from filter cartridge, remove and discard plastic shield from top of cartridge.
7. Insert cartridge into head by pushing up and turn until it locks into place.
8. The filter now needs to be activated:
1. Place free end of hose connected on outlet into a bucket or similar.
2. Turn on water supply and allow at least 15 litres of water to run through the filter system.
3. Turn off water supply and connect hose to ice machine.
4. Turn on water supply; machine and filter are now ready for use.

Note: Filter cartridge will require replacing in approximately 6 months on average quality water. In hard/poor quality water areas, this may be sooner.

IMPORTANT!

IF YOU HAVE ANY QUERIES CONCERNING INSTALLATION OF YOUR WATER FILTER KIT EMAIL YOUR QUESTION DURING OFFICE HOURS TO:

help@misterchill.co.uk

Installation of All Models

Unpacking

• Remove two of the banding strips securing equipment to pallet.
• Remove cardboard carton and packaging material.
• Inspect exterior of machine for damage.

Open bin door and remove :

• 1 x water inlet tube
• 1 x drain tube complete with clip
• 1 x leg kit (not supplied on Ice One)

Remove transit tape from ice curtain and spray plate.

Check ID on rear of machine for correct voltage, e.g. 230 volt 50 hz for UK use.

Remove protective film from outer panes.

Installation

Check following services are within 1 metre of machine location:

• Cold water supply terminated with a washing machine style stop valve.
• Mains drainage with a connection point lower then the drain outlet of the machine. Connection point must be at least 1 ¼" diameter open and trapped (similar to a domestic washing machine). If drain is too high a stand or condensate pump must be used.
• 13 amp socket outlet. Due to high starting current, a two or three way adaptor with other appliances must not be used.

Note:

If a condensate pump is to be used, then 2 x 13 amp socket outlets are required.

Check the following:

• Ambient temperature - minimum 10°C, maximum 40°C
• Adequate space at rear of machine for water and drain connections.
• Minimum clearance of 15cm to both sides of machine.

Note:

If clearance is less, ice production rate will decrease by as much as 25% due to overheating.

Fit legs to Ice Two, Three, ACM55, ACM85, ACM105, ACM125, ACM175 and ACM225.

Level equipment in both directions : left to right and front to rear.

Fit 13 amp plug top (fitted with 13A fuse) to mains lead.

Fit water inlet hose to machine. Do not overtighten.

Fit flexible drain hose to machine and secure using clip provided.

Note:

Both hoses are fitted with one straight end and one angled end. Use which ever is the most suitable for that installation.

Connect water inlet hose to water supply. Do not overtighten.

Connect drain hose to main drain by inserting hose into upstand (similar to domestic washing machine).

Note:

To prevent drainage problems caused by loops in the hose, reduce hose length as far as practicable.

Remove front panel of machine.

Locate switch on control panel and move to position II.

Start Up

Turn on water and power supply.

At this point water will enter the machine and fill the water tank, the water pump and fan motor will also run.

When the water tank is full and excess water is running through the drain, move switch back to position I. The machine will now start an ice making cycle.

After approximately 25 minutes, ice cubes will fall through the curtain and into the storage bin. The machine will automatically refill with water and start the next cycle.

Count and inspect the cubes:

• Ice One = 18
• Ice Two = 24
• Ice Three = 24
• ACM 45 = 18
• ACM 55 = 24
• ACM 85 = 24
• ACM 105 = 32
• ACM 125 = 48
• ACM 175 = 48
• ACM 225 = 102

Each cube should be clear and solid with a small depression of about 6mm at the base.

If the depression is greater than 6mm adjust the thermostat, fitted with a knob – one- eighth turn clockwise and recheck after the next cycle.

If the depression is less than 6mm or the cube is rounded at the base, adjust the thermostat counter clockwise one - eighth turn and recheck after next cycle.

The above procedures are designed to supplement guidance given in the user handbook, not replace it.

IMPORTANT!

IF YOU HAVE ANY QUERIES CONCERNING INSTALLATION OF YOUR WATER FILTER KIT EMAIL YOUR QUESTION DURING OFFICE HOURS TO:

help@misterchill.co.uk